Sub-Surface Scattering (SSS) simulates the effect of light entering an object and scattering beneath its surface. Not all light reflects from a surface. Some of it will penetrate below the surface of an illuminated object. There it will be absorbed by the material and scattered internally. Some of this scattered light will make its way back out of the surface and become visible to the camera. This is known as 'sub-surface scattering' or 'SSS'. SSS is necessary for the realistic rendering of materials such as marble, skin, leaves, wax, and milk. The SSS component in this shader is calculated using a brute-force raytracing method.
You must ensure that the geometry normals are pointing in the correct direction, otherwise, SSS will not render correctly.
SSS is important when replicating realistic materials such as plastics, for example:
The 'blend' between diffuse and subsurface scattering. When set to 1.0, there is only SSS, and when set to 0 it is only Lambert. In most cases, you want this to be 1.0 (full SSS).
The color used to determine the subsurface scattering effect. For example, replicating a skin material would mean setting this to a fleshy color.
The approximate distance up to which light can scatter below the surface, also known as “mean free path” (MFP). This parameter affects the average distance that light might propagate below the surface before scattering back out. This effect on the distance can be specified for each color component separately. Higher values will smooth the appearance of the subsurface scattering, while lower values will result in a more opaque look.
The lighter the color, the more light is scattered. A value of 0 will produce no scattering effect:
Increasing the radius value can radically change the appearance of the material, from looking like leather to marble. SSS is very scale dependent. You will need to adjust the radius multiplier depending on the size of your model. If you were to render using the default SSS settings, you might get something that does not look correct. Alternatively, adjusting the scene scale can have similar results.
Instead of distributing all of the colors with the same amount, you can also choose different radius values for each of the RGB colors. For example, a material like clay or skin should have a higher red radius than green and blue.
When rendering skin, you should use a value like 1.0, 0.35, 0.2, indicating that red should scatter deepest and green and blue less. This would replace the three-layer workflow (deep, mid and shallow layers) for skin where you would make the deep layer red to indicate that deep should scatter with a larger radius. Setting scatter_radius.R to a larger value would correspond to that.
The images below show the effect when increasing the red color of the radius. Notice the colored 'fringing' effect around the edges of the circles. The same effect occurs when Gaussian blurring the red channel of the source image in a compositing package.
Controls the distance that the light is likely to travel under the surface before reflecting back out. It scales the scattering radius and multiplies the SSS Radius Color.
If the scene is in meters, then SSS Scale can be set to 0.01 to specify the SSS Radius in centimeters. For example for skin, the SSS Radius could be 0.37cm, 0.14cm, 0.07cm.
Choose between diffusion or randomwalk (diffusion is used by default, so as not to break the look of existing scenes). Unlike the empirical BSSRDF method based on diffusion theory, the randomwalk method actually traces below the surface with a real random walk and makes no assumptions about the geometry being locally flat. This means it can take into account anisotropic scattering like brute-force volume rendering and produces much better results around concavities and small details. It can also be substantially faster for large scattering radius (i.e. large mean free path) compared to diffusion. On the other hand, randomwalk can be slower in dense media (i.e. small mfp), does not support
sss_setname for blending two surfaces together, may require redialing materials to achieve a similar look, and is more sensitive to non-closed meshes, "mouth bags", and internal geometry potentially casting shadows.
Henyey-Greenstein Anisotropy coefficient between -1 (full back-scatter) and 1 (full forward-scatter). The default is 0 for an isotropic medium, which scatters the light evenly in all directions, giving a uniform effect. Positive values bias the scattering effect forwards, in the direction of the light, while negative values bias the scattering backward, toward the light.
This parameter only works with the randomwalk SSS method.
SSS Between Objects
It is possible to tag multiple objects as belonging to the same SSS 'set' so that illumination will blur across object boundaries. A common use-case might be blurring between teeth and gum geometry. It is enabled by adding the constant STRING userdata sss_setname to the same value on the objects in the set.
This currently does not work with the randomwalk SSS method.